A Word on Build Quality

All things considered, PCBs aren’t very stiff. The additional layers in a PCB help reinforce it somewhat, but this is a byproduct of constructing the card rather than an intentional design element to improve rigidness. As a result, additional steps need to be taken to reinforce PCBs, particularly those large cards.

At the top of the spectrum we have monster cards like the Radeon HD 5970, the GTX 295, and even specialty cards like the Asus Ares. Rather than mounting elements on to the card, these cards are practically mounted inside of a metal shell, necessary to provide support and to draw out heat from their various components. Below that we have cards like the GTX 480 and Radeon HD 5850 which have a metal plate or cooler on the front of the card that the PCB is mounted to. And finally below that we have cards like the GTX 460, Radeon HD 5770, and GTS 450, where the PCB must stand alone and support the cooler.

Depending on the size and the layout of the cooler, additional steps need to be taken to reinforce the card in order to prevent flexing of the PCB. Case in point, the GTS 450 and GTX 460 have small foam spacers on the PCB that keep the PCB from flexing towards the cooler, where there’s a roughly 4mm gap between it and the PCB. Other cards like the most common Radeon HD 5770 designs don’t have any reinforcement, supporting everything with the PCB.

Reference GTS 450 With Foam Spacer

Up until this past week, I’ve never received a card that looked bent. Certainly if I dig through my entire collection and measure every free-standing card I could definitely find something that has a slight flex to it, but I’ve never had a card that you can tell is bent just from looking at it.

This changed when I received the first of our vendor samples, Sparkle’s Calibre X450G, a reference-PCB card with a massive Arctic Cooling Accelero Twin Turbo Pro cooler. The Twin Turbo Pro is a heatsink that runs the entire length of the card, and then on top of that is a pair of 92mm fans. All told the cooler takes up 3 slots, making it by far the biggest GTS 450 in our roundup and the best cooled.

But it has an issue. That massive heatsink is free-standing, supported by nothing other than the 4 mounting bolts around the GPU. At the front and the rear of the card, far from the GPU, there’s nothing supporting the heatsink. Or rather given the size disparity, there’s nothing supporting the PCB.

Calibre X450G W/Bowing PCB

As a result the PCB on our sample card is noticeably bent – it’s the first card I’ve ever had arrive as such. Whether this happened during manufacturing or on the long flight from Taiwan is anyone’s guess, but the outcome is that the PCB clearly bends towards the cooler.

Make no mistake: the card works just fine. It passes all of our tests, overclocks fairly well, and is ridiculously cool compared to the other cards in this roundup. At the moment at least it’s bent without any measurable downsides. But it’s not supposed to be bent, and this is the core of our worries.

The problem with bending of course is that it risks damaging solder joints – the wave soldered GPU and GDDR5 memory are the most intricate and most vulnerable components. While the card is fine at the moment, we have concerns about the reliability of the card in the long term. Will it hold up in 1-2 years with repeated heating and cooling cycles? This isn’t something we normally worry about, but when the PCB is permanently bent it becomes something of a concern.

Ultimately the card is a victim of bad build quality. The card should not have shipped without further reinforcement to the PCB to prevent just this situation, and this is something we’ve told Sparkle. In fact Sparkle even has a patented technology – VGA Rectifier Technology – that solves this problem by providing the card with a metal “spine” which should prevent the warping of the PCB. At this point Sparkle has not been able to tell us why the card did not ship with VRT, so we can only fathom to guess that their engineers did not believe the PCB would warp to the extent our samples has. Or perhaps for that matter we just got an especially bad card, but if that’s the case then how many more cards will ship like this? It’s a rare thing when we can say there’s something physically wrong with a card.

 Moving on, this is not the end of our story. As exceptional as it is to receive 1 card with a warped PCB, it’s truly bizarre to receive a 2nd card, but that’s what happened to us last week. One of the last cards we received was the EVGA GTS 450 FTW, a pure reference card that should be identical to the NVIDIA reference card. But we found one small thing that made all the difference.

Remember the foam spacer on the GTX 460 and GTS 450 that we previously mentioned? It’s missing on our FTW sample. And as you may have already guessed, as a result the PCB is warped.

EVGA GTS 450 FTW, Missing Its Foam Spacer

Unlike the Calibre card the warping here is not even a fraction as bad; at its worst we’re only measuring the PCB as being 1mm closer to the cooler than it is on our reference cards with their spacers. In all honesty if it wasn’t for the fact that we have reference cards with the spacers, we likely would not have even noticed it. But it’s there, and when we know what to look for it’s easy to spot compared to the edge of the shroud running parallel to the PCB. It looks like there’s a good reason for those foam spacers after all.

In any case a 1mm bend in the PCB does not appear to be a problem; as we said before we could probably find a free-standing card in our collection with a similar bend if we looked hard enough. So unlike the Sparkle card we’re not the least bit worried about the long-term effects of the warped PCB on this card. At its worst it’s a good example of why PCB reinforcement should not be overlooked.

Wrapping up our story with EVGA, a few hours before the GTS 450 launch we got a call from them asking for more information. This 1mm bend that even we weren’t concerned about got their attention, and as a result EVGA temporarily halted shipment of the GTS 450 FTW until their engineers could look in to the issue. It’s clear that the foam spacers are supposed to be there, and at this point EVGA is trying to figure out which cards (if any) may have left the factory spacer-less and why the PCB would have warped without them. Based on their own internal sampling, it sounds like the bending may ultimately be a product of overtightening the heatsink when it was mounted.

We’ll update this article with more information once EVGA can fully analyze the issue, but for the time being kudos to EVGA for stepping up to the plate and halting shipment for what’s probably nothing worse than a minor cosmetic issue. It’s a potentially costly move on their part that’s the embodiment of good customer service.

Finally, we also have a GTS 450 card in this roundup that goes through exemplary measures to prevent warping that we’d like to quickly discuss: the Asus ENGTS450 Top. The ENGTS450 Top uses a custom cooler mounted on what appears to be a reference-derived PCB. The cooler is different enough that Asus can’t simply pad it to protect against bending, so instead they go all the way.

Asus ENGTS450 Top With A Metal Spine

At the top of the card is a metal spine (GPU Stiffer Bracket) running just short of the length of the card which prevents flexing. Further augmenting this is a heatsink covering the VRMs, which in turn the GPU heatsink sits directly on top of. With no gap between these heatsinks the PCB doesn’t have room to bend towards the cooler, and the metal spine ensures that it doesn’t bend anywhere else either. Next to encasing the card in a metal body it’s as solid as a card can get – even futuristic alcohol-swilling robots would have trouble bending this card. We rarely get the opportunity to credit a well-built card, but in this case it’s clear that Asus has one.

NVIDIA GeForce GTS 450 Launch Roundup: Asus, EVGA, Palit, and Calibre Overclocked and Reviewed Asus ENGTS450 Top
Comments Locked


View All Comments

  • gwolfman - Monday, September 13, 2010 - link

    When do we get our first single slot Fermi? I'd like one to offload my PhysX. Any ideas?
  • Slash3 - Monday, September 13, 2010 - link

    Looks like an error on the first page's chart, the memory clock box for the reference card should be at a 3.6GHz data rate and not 4.6GHz, correct?
  • anactoraaron - Monday, September 13, 2010 - link

    And their responce to the bending issue is why they are just the best to work with (and buy from) for anything - including RMA's. They are first in that category (customer service) hands down. Over the course of 7 years, I have had to RMA something (at least one item) to ASUS, HIS (the worst by far), Gigabyte and EVGA. EVGA FTW!
  • Voldenuit - Monday, September 13, 2010 - link

    Warping, like all of life's problems, is just a special case of bending.
  • Shadowmaster625 - Tuesday, September 14, 2010 - link

    You guys should simulate 2-3 months of heavy dust collecting inside a PC case. Then run the furmark power consumption and heat tests. Then you might understand why people want a card like the Calibre X450G.
  • HangFire - Thursday, September 16, 2010 - link

    2-3 months does not make for heavy dust in any of my PC cases. 2-3 years would, but none run that long before getting cleaned out.

    The real market for the Calibre would be the silent PC crowd, who would otherwise pay extra for an Accelero (or other aftermarket GPU cooler), and would be happy to pay a smaller premium for a pre-installed cooler- and keep their warranty too.
  • tech6 - Tuesday, September 14, 2010 - link

    Since you can get a 5770 from NewEgg for $125 (with rebate) and GTX460 for $170, I don't see why any of these cards make much sense unless they will be heavily discounted.
  • JPForums - Tuesday, September 14, 2010 - link

    <quote>Since you can get a 5770 from NewEgg for $125 (with rebate) and GTX460 for $170, I don't see why any of these cards make much sense unless they will be heavily discounted. </quote>

    At $130 straight up these GTS450s make plenty of sense (especially if you don't want to deal with the sometimes less than reliable rebate system). They may not be quite as good a value as a $125 HD5770, but they are still a good buy. (particularly if you require an nVidia card) Of course, a GTX460 will net you a healthy performance boost for an equally healthy price bump.
  • Spazweasel - Tuesday, September 14, 2010 - link

    They still do. Look in the part number. If it ends in "AR" it's lifetime warranty, if it's "TR" the warrant is (I think) 2 years. The price difference is generally 10 to 20 dollars, depending upon the base price of the part.
  • shin0bi272 - Tuesday, September 14, 2010 - link

    Id rather have a gtx470 super overclock from gigabyte. yeah its twice the price but its more than twice the speed. The gigabyte 470 soc out performs a gtx480 but costs 100 bucks less. So why go out and have to buy 2 450's to get halfway decent performance when you could buy 1 470 and spend the same amount?


Log in

Don't have an account? Sign up now